High Noon W650 Speedwerks

Однажды местный гонщик обратился в мастерскую Speedwerks. Он загорелся идеей собственного каферейсера, которых уже не раз видел, и хотел себе мотоцикл, на котором можно выезжать и гонять в любое время. Так был спроектирован и воплощен в жизнь проект уникального мотоцикла с двигателем от Kawasaki W650 под названием High Noon.

  • Рама работы Марка Роу;
  • Обновленная проводка и зажигание;
  • Литий-ионный аккумулятор;
  • Вилка Yamaha, модернизированная пружинами Race Tech;
  • Суппорты Brembo и сделанные под них индивидуальные крепления;
  • Замена амортизаторов на более современные;
  • Седло, топливный бак, крылья и много других небольших кастомных новшеств.

Delaware-based Speedwerks were in an enviable position. They’d been approached by a long-term customer wanting a balls-to-the-wall café racer that could be ridden hard and ridden every day. The customer, local racer and speed boat enthusiast known only as ‘Richie’, had seen a few Deus café racers and wanted something in a similar vein, but louder and better engineered than anything that had come before. Armed with only a Kawasaki W650 engine stripped of its electric start, Speedwerks surveyed the line-up of modern retro motorcycles for a donor frame and found few that could blend traditional looks with modern geometry and stiffness. So they went about designing one. On the back of a beer-soaked napkin at a local sports bar.

Speedwerks is based less than a mile from Marc Rowe, a local chassis guru who had helped the team with a few previous builds. But building the frame for the W650 was the perfect opportunity to spend some more time working under his tutelage, with Richie not pushing the team for time. “I spent every evening for the next two years drinking beers, bending tubes and making metal chips with Marc,” said Steve Long, head designer at Speedwerks, “He’s the most badass old-school machinist on the planet, period.”

And Marc has the resume to back it up. He’s won Monster Garage and built frames for Aerosmith’s cruiser company Dirico. “If you can imagine it, Marc and Budweiser can make it.” The knowledge that Marc brought to the build, and to the workshop, can’t be underestimated. “I’ve never learned more from one person in my life and unfortunately, his kind are a dying breed”, Steve says.

For a blueprint sketched on the back of a serviette over a few drinks, Marc did a remarkable job creating the tight, stiff frame that pins the W650 engine firmly in place. And its slick lines aren’t just for looks, with the backbone also doubling as a crankcase catch and vent and also a hiding place for clutch cables and the wiring loom, which feed into an Ignitech programmable ignition and lithium-ion battery. The genius of the design doesn’t end there, with the rear fender able to slide in and out of the frame to hold the licence plate. Those two years certainly didn’t go to waste.

And all that careful work on the frame is matched by a no-compromise approach to the suspension, which carefully marries modern stopping power with traditional lines. Up front a pair of conventional 41mm Yamaha forks were shaved down and Race Tech springs and emulators mounted inside.

Speedwerks designed billet radial mounts for Brembo monoblock calipers, so it would have the look of a conventional fork with the stopping power of an improved inverted radial mount. The rear runs a matching brake setup while a pair of Kawasaki ZRX1200R shocks, shortened, re-valved and re-sprung, help keep the tail end of the bike in line.

Just about everything else you see on the bike was designed and manufactured in-house. The chrome-moly swingarm is also their own creation and the arched steel tank, close-hugging front fender and alloy seat pan were all sketched out and manufactured by the capable team.

The level of fabrication doesn’t end there – look closer and you’ll see that all the ancillary parts were also designed by the guys at Speedwerks, including the triple trees, brake hangers and motor mounts which were all CNC’d from billet aluminium.

Despite the ostentatious 70’s-inspired paint scheme completed by John Walls the bike still manages to show an appreciation for the finer touches in a build – and helps me realize how little I know about bike building, fabrication and the black art of frame design. Starting with only an engine, the workshop have managed to create a unique, functional motorcycle held together by a chrome-moly piece of automotive, beer-fuelled genius.

Model info
Year introduced 1999
Year discontinued 2006
Original price
Used price £3,800 to £4,500
Warranty term (when new) Two year unlimited mileage
Running costs
Insurance group 8 of 17
Annual road tax £82
Annual service cost £30
Max power 49 bhp
Max torque 41 ft-lb
Top speed 110 mph
1/4-mile acceleration 14.2 secs
Average fuel consumption 51 mpg
Tank range 165 miles
Engine size 675cc
Engine type 8v parallel twin, 6 gears
Frame type Steel double cradle
Fuel capacity 15 litres
Seat height 800mm
Bike weight 195kg
Front suspension None
Rear suspension Preload
Front brake Single 300mm disc
Rear brake Drum
Front tyre size 100/90 x 19
Rear tyre size 130/80 x 18